Smyrna office(615) 223-9600Call now Smyrna (Nashville & Middle TN) officeChattanooga office(423) 344-3787Call now Chattanooga officeNationwide(615) 223-9600Call now Smyrna (Nashville & Middle TN) office
Looking for business IT?Meet TechCore

When Does a Security System Need Fiber Optic Cable?

By the Turner Security team · · 6 min read

Technician at a work table inside a utility van using a fusion splicer to join two strands of yellow fiber optic cable, with a camera pole and gate visible through the open door

Short answer: A security system needs fiber optic cable when a camera, gate controller or building is too far away for copper network cable, or when the copper run would be exposed to lightning, ground problems or electrical interference. Standard Cat5e, Cat6 and Cat6A Ethernet is limited to a 100 meter channel (about 328 feet, including patch cords), while fiber runs hundreds of meters on multimode and kilometers on single-mode. Fiber also carries no electricity, so it doesn't connect the electrical grounds of two buildings or carry a lightning surge from a pole into your network rack.

Most security devices inside a building are fine on copper. The trouble starts at the edges of a property: the camera pole at the back of the lot, the gate at the end of the drive, the guard shack, the second warehouse across the yard. Those are the runs where fiber earns its keep.

When should a security system use fiber instead of Cat6?

Here are the situations where we recommend that business owners at least price fiber:

Situation Why copper struggles Why fiber helps
Device more than 100 m (328 ft) from the network switch Ethernet over twisted pair is specified to a 100 m channel Fiber runs far past that limit
Link between two buildings Copper ties the two buildings' electrical grounds together Fiber is non-conductive, so there is no electrical path
Camera poles and gates in open lots Long outdoor copper can pick up lightning surges No metal path for a surge to follow into the rack (unless the cable has metal armor, which must be grounded)
Runs near motors, generators or heavy electrical equipment Electrical noise can corrupt data on copper Fiber is immune to electromagnetic and radio interference
Main backbone carrying many cameras High camera counts need more bandwidth Fiber has far more headroom for growth

The 100 meter rule

The cabling standard behind most business networks (TIA-568) sets a 100 meter limit for a twisted pair copper channel: up to 90 meters of installed cable plus up to 10 meters of patch cords. Past that, you can start getting dropped video, cameras that reboot and Power over Ethernet devices that don't get enough power. There are extenders and long reach products, but for a run that is well past 100 meters, or for a device you can't afford to lose, fiber is usually the cleaner answer.

Outbuildings, gates and parking lots

When copper connects two buildings, it also connects their grounding systems. If the grounds sit at different voltages, current can flow through the data cable and cause errors. A nearby lightning strike can raise one building's ground potential and send a surge down the copper, damaging switches and recorders on the other end. Surge protectors help with short spikes but don't fix steady ground differences. A fiber link breaks the electrical path completely. That's why fiber is a common choice for warehouses and distribution sites with guard shacks, yard cameras and multiple buildings.

One thing fiber doesn't carry: power

Fiber carries data, not electricity. A camera or access control panel at the end of a fiber run still needs power, either from a local power source with a small switch or media converter, or from a hybrid cable that carries copper conductors for power alongside the fiber. Planning power is part of every fiber design.

Single-mode or multimode: what's the difference?

Both carry light. The difference is the size of the glass core and how far the signal can travel.

  • Multimode has a larger core (50 or 62.5 microns) and is common for shorter runs on a campus or inside a large building. Cable jackets are usually aqua for OM3 and OM4. Typical distances: OM3 supports about 300 meters at 10 gigabits and about 550 meters at 1 gigabit, and OM4 about 400 meters at 10 gigabits.
  • Single-mode has a tiny core (about 8 to 10 microns), usually a yellow jacket, and carries signals for kilometers. It is the usual choice for long runs, big properties and anything that might be extended later.

Single-mode carries the longest distances and leaves the most room to extend the network later. Multimode can make sense for shorter runs. Your installer should explain why they picked one over the other for your site.

What is fusion splicing, in plain terms?

Fiber strands are thinner than a human hair, and every joint between two pieces of fiber loses a little light. There are two ways to join them.

Fusion splicing uses a machine that lines up two cleanly cut fiber ends and welds them together with an electric arc. The result is a permanent, strong joint. A good fusion splice can lose less than 0.1 dB of signal, which is close to unbroken fiber.

Mechanical splicing holds the two fiber ends together in a small fixture, usually with an index matching gel between them. It's quicker and doesn't need an expensive splicer, but loss is higher (roughly 0.2 to 0.75 dB), the gel can degrade over time and it is harder to do well on single-mode fiber. Today mechanical splices are mainly used for emergency repairs and temporary connections.

The TIA-568 standard allows up to 0.3 dB per splice of either type, but good installers aim well below that. On a long link with several splices and connectors, the small differences add up.

Turner Security installs fiber for security systems, including fusion splicing, so one company handles the fiber and the cameras, access control and network gear on each end of it.

What should you ask a fiber installer?

  • Single-mode or multimode, and why? Make them explain the choice for your distances and future plans.
  • How many strands are you pulling? Extra strands cost little during installation and save a whole new pull later.
  • Fusion splices or mechanical? For permanent links, fusion is the standard choice.
  • What kind of cable for outdoor runs? Outdoor and underground runs need cable rated for water and sunlight. If the cable has metal armor, ask how it will be grounded.
  • How will devices at the far end be powered?
  • How will the link be tested, and will I get the results? Ask for test reports with each strand labeled.
  • Where will splices and spare cable be stored? Splice enclosures and labeled patch panels make future service much easier.

How is fiber tested?

There are two common levels of testing:

  1. Light loss testing (Tier 1). A light source sends a known signal into one end, and a power meter measures what comes out the other. This confirms total loss, length and polarity, and it is the test the standards call for to certify a link. It gives a clear pass or fail against the loss budget for that link.
  2. OTDR testing (Tier 2). An optical time domain reflectometer sends pulses down the fiber and reads the reflections, producing a trace that shows each splice, connector and bend along the run and how much loss each one adds. It's optional under the standards, but it is the best tool for troubleshooting and documenting long outdoor runs.

Ask for light loss results at minimum. On long runs or links with several splices, an OTDR trace is a useful record to keep with your system documents.

FAQ

Can I run Cat6 to a camera 400 feet away?

400 feet is past the 100 meter (328 foot) channel limit for Ethernet. You'd need an extender, a switch in between with its own power, or fiber. For an outdoor pole or a gate, fiber is often the most reliable option.

Is fiber more expensive than copper?

It often costs more to install per run because of splicing, termination and the equipment on each end. On long runs, between buildings or in lightning exposed spots, it may cost less over time by avoiding repeat equipment damage. The only way to know for your site is a quote that prices both.

Does fiber work for access control at a gate?

Yes. Fiber can carry the network connection to a gate controller or a network switch at the gate, which then connects card readers, intercoms and cameras. Learn more about commercial access control.

How long does fiber last?

Properly installed fiber has a long service life. Most problems come from physical damage, like a cut during digging, which is why splice records and route maps matter.

Get fiber planned with the rest of your system

Turner Security designs and installs business security camera systems, access control and the network that ties them together, including fiber runs and fusion splicing for distant cameras, gates and outbuildings. Request a free security assessment and we'll walk the property, measure the runs and tell you where copper is fine and where fiber is worth it. See our full range of commercial security systems.

Commercial security systems

Intrusion alarms, cameras and access control planned around how your business runs.

Learn about commercial security systems

Want a second opinion on your setup?

Book a free walkthrough with a local Turner Security tech.

Smyrna office(615) 223-9600Call now Smyrna (Nashville & Middle TN) officeChattanooga office(423) 344-3787Call now Chattanooga officeNationwide(615) 223-9600Call now Smyrna (Nashville & Middle TN) office
Talk to Turner Security

Ready to secure your business?

Send a quick message and the right Turner team will get back to you. Prefer to talk? Call the office closest to you.

Smyrna office(615) 223-9600Call now Smyrna (Nashville & Middle TN) officeChattanooga office(423) 344-3787Call now Chattanooga officeNationwide(615) 223-9600Call now Smyrna (Nashville & Middle TN) office

Fields marked with an asterisk are required.