Smyrna office(615) 223-9600Call now Smyrna (Nashville & Middle TN) officeChattanooga office(423) 344-3787Call now Chattanooga officeNationwide(615) 223-9600Call now Smyrna (Nashville & Middle TN) office
Looking for business IT?Meet TechCore

Fire protection

VESDA aspirating smoke detection systems, designed, installed and serviced

Turner Security designs, installs and services VESDA and other aspirating smoke detection systems for data centers, server rooms, high-ceiling warehouses and high-value inventory sites. We tie each system into your fire alarm panel and keep it inspected and tested, for businesses nationwide from hubs in Smyrna and Chattanooga, Tennessee.

50 yrsin business
2local offices
Security + ITone company
Fire alarm technician testing wiring inside an open commercial fire alarm control panel

What does a VESDA installation include?

A VESDA or aspirating smoke detection project covers four things: designing the pipe network and sampling holes for the space, installing the detector and piping, connecting the detector to the building's fire alarm panel, and commissioning and testing the system so it is ready for the fire marshal. After that, the system needs periodic inspection, testing and filter service.

Turner Security handles all of it. We are a family company that has served businesses since 1976, with offices in Smyrna and Chattanooga, Tennessee, and national accounts in other states. If you want to understand how aspirating detection works before you buy, start with our guide to VESDA aspirating smoke detection.

  • DesignPipe network and sampling hole layout planned around the room, airflow and ceiling height
  • InstallationDetector, sampling pipe and wiring installed and labeled
  • IntegrationAlarm and fault signals tied into your fire alarm panel
  • ServiceCommissioning, inspection, testing, filter service and repairs
  • Licensed and accreditedTennessee Alarm Contracting Company licenses #319 and #1998, BBB Accredited since 1993 with an A+ rating
  • 50Years serving businesses, since 1976
  • 33Years BBB Accredited, with an A+ rating
  • 2Tennessee hubs, in Smyrna and Chattanooga
Where it is used

Spaces where businesses choose aspirating smoke detection

No law requires VESDA or aspirating detection for most businesses. It is usually chosen because a fire, or the smoke from one, would shut down operations or destroy inventory, and in some cases because an insurer, an owner's standard or a facility standard such as NFPA 76 for telecommunications facilities calls for very early warning detection. Before you design around a requirement, confirm it with your local fire marshal and your insurer.

Data centers

White space, raised floors and hot and cold aisles, where strong cooling airflow can dilute smoke before it reaches ceiling detectors.

Telecom and server rooms

Equipment rooms and closets where an early warning can give staff time to find an overheating component before it becomes a fire.

High-ceiling warehouses

Tall spaces where smoke can thin out before it reaches the roof, and where ceiling detectors are hard to reach for testing. The detector can sit at floor level.

Clean rooms

Controlled environments with high air change rates, where piping can sample air without putting spot detectors in the room.

High-value inventory sites

Firearm dealers, records storage and other sites with stock that is expensive or slow to replace, where earlier warning means more time to act.

Mechanical and electrical rooms

Switchgear, battery and electrical rooms that support critical operations and are worth watching closely.

Why Turner

One company for VESDA, fire alarm and security

Turner Security is a family company that has served businesses since 1976 from hubs in Smyrna and Chattanooga, Tennessee, and we serve businesses nationwide, including multi-site national accounts. Because we also handle fire alarms, cameras, access control and intrusion alarms, your early warning detection can be serviced by the same team that knows the rest of your building.

We don't require long-term contracts, we offer same-day service scheduling, and every project starts with a free security assessment.

  • Family company since 1976
  • Tennessee Alarm Contracting Company licenses #319 and #1998
  • BBB Accredited since 1993, A+ rating
  • No long-term contracts
What we handle

VESDA work from first layout to annual testing

An aspirating system is only as good as its pipe design and its connection to the rest of your fire alarm. We plan both before anything is installed.

System design

We lay out the sampling pipe, hole locations and detector placement for the space, including racks, raised floors, ceiling voids and areas with strong airflow.

Detector and pipe installation

We install the detector where it is easy to reach, run the sampling pipe and label it so the next inspection or change is straightforward.

Fire alarm panel integration

We connect the detector's alarm and fault outputs to your fire alarm panel, so its warnings show up on the system your building already relies on.

Commissioning

We set alarm thresholds for the space and test smoke at the far end of the pipe to confirm it reaches the detector within the time NFPA 72 allows.

Inspection and testing

Scheduled inspection and testing of airflow, filters, alarm levels and panel signals, with documentation you can keep on file.

Service and repairs

Troubleshooting airflow faults, cracked or blocked pipe, dirty filters and panel communication problems on systems we installed or inherited.

Why it matters

Early warning only helps if the system is designed and kept right

Aspirating detection is chosen for spaces where a fire would be expensive before it is ever large: server rooms, telecom equipment, stored inventory that cannot be replaced quickly. That value depends on details like hole spacing, pipe length, airflow and thresholds set for how the room is actually used.

A system that sends a fault nobody responds to, or that is never tied into the fire alarm panel, gives a false sense of protection. We design it, install it, connect it and keep testing it, so one company is responsible for the whole job.

  • Pipe network designed for the space
  • Tied into your fire alarm panel
  • Commissioned and documented
  • Inspection, testing and service after install
Fire alarm technician testing a pull station below a horn strobe in a commercial hallway
Fire and security togetherOne company for the whole system
How it works

How a VESDA project works

Clear scope before any pipe goes up.

Site review

We look at the space, how it is used, ceiling height, airflow and the fire alarm panel the system will connect to.

Design and proposal

We lay out the pipe network and detector locations and give you a written proposal with a clear price.

Install and integrate

Our technicians install the detector and piping and connect alarm and fault signals to your fire alarm panel.

Commission and service

We set thresholds, test transport time and every signal, then keep the system inspected and serviced.

Panel integration

Connecting VESDA to your fire alarm panel

An aspirating detector has its own alarm levels. A VESDA detector typically uses four, often called Alert, Action, Fire 1 and Fire 2, so it can raise an early warning well before it calls for a full alarm. How those levels reach your fire alarm panel decides what happens next: an early level might go to a supervisory or pre-alarm point for staff to investigate, while a fire level activates the building alarm.

Detectors usually connect through relay outputs or a high-level interface, depending on the detector and the panel. We check what your existing panel supports, map each level to the right response with your team and fire code official, and test every signal end to end. If your fire alarm needs work at the same time, our commercial fire protection team handles the panel side too.

Commercial fire protection

Fire alarm installation, inspection and service for the panel your VESDA system reports to.

Inspection and testing

Keeping an aspirating system ready for the fire marshal

Aspirating smoke detection falls under NFPA 72, the same code that governs the rest of your fire alarm system, and your local fire code official decides how it is enforced. Testing generally includes confirming airflow, servicing filters, checking that smoke introduced at the sampling holes reaches the detector, and verifying that each alarm and fault signal reaches the fire alarm panel. We plan inspections around what your fire marshal expects and keep the records ready.

  • Transport time and airflow checks
  • Filter service and detector testing
  • Alarm and fault signals verified at the panel
  • Written reports for your files
Common questions

Questions we hear a lot

Do you install VESDA systems?

Yes. Turner Security designs, installs, integrates and services VESDA and other aspirating smoke detection systems, including the connection to your fire alarm panel and ongoing inspection and testing.

Is VESDA required by code?

For most businesses, no. No law generally requires VESDA. It is usually chosen for spaces where early warning protects equipment, operations or inventory, and some insurers, owners or facility standards such as NFPA 76 for telecommunications facilities call for very early warning detection. Confirm your requirements with your local fire marshal and your insurer.

How much does a VESDA system cost?

Cost depends on the size and layout of the space, how many detectors and how much sampling pipe it needs, ceiling height, and how the system connects to your existing fire alarm panel. We review the space and give you a written proposal with a clear price.

Can VESDA connect to my existing fire alarm panel?

Usually, yes. Aspirating detectors connect through relay outputs or a high-level interface. We check what your panel supports and map each alarm level to the right response before installation.

Does VESDA replace sprinklers or a fire suppression system?

No. VESDA detects smoke and sends warnings. It does not put out a fire. Your sprinklers or suppression system, and the fire alarm, still need to meet the requirements for your building.

How often does an aspirating smoke detection system need to be tested?

Testing follows NFPA 72, the manufacturer's instructions and your local fire code official. It generally includes airflow and filter checks, smoke tests at the sampling holes and verification of every signal at the fire alarm panel. We set up a schedule that fits your building and keep the reports.

Do you work on VESDA systems outside Tennessee?

Turner Security serves businesses nationwide from hubs in Smyrna and Chattanooga, Tennessee. Fire alarm work is licensed and permitted locally, so tell us where your site is and we will tell you how we would handle the project there.

What is the difference between VESDA and a regular smoke detector?

A regular spot smoke detector waits for smoke to drift to it. An aspirating system pulls air through sampling pipes to a sensitive detector, which can pick up smoke earlier and from places spot detectors are hard to use. Our guide to VESDA aspirating smoke detection explains the technology in more detail.

Related services

Plan the connected parts together

National accounts

One security and fire program across all your locations.

Looking for business IT?

Networks, IP phones, servers and managed IT are handled by our sister company, TechCore. Same owners, same local team, one call for security and IT.

  • Managed IT
  • Networks and Wi-Fi
  • Servers and cloud
  • Business IP phones
Meet TechCore
What customers say

Five-star reviews from real customers

Richard really helped us out when we had issues with our fire monitoring at our box plant.

joberson731 Google review, 5 stars

Prompt, friendly and there whenever you need them. Provide great protection.

Simon M. Google review, 5 stars

Turner is extremely dedicated to its customers. They go above and beyond what is expected of them. Turner's resolve on all issues is to treat you as if you are their own family.

Tracy C. Google review, 5 stars

Read more reviews

Planning VESDA for a data room, warehouse or high-value site?

Tell us about the space and your fire alarm panel, and we'll scope the system and give you a clear price.

Smyrna office(615) 223-9600Call now Smyrna (Nashville & Middle TN) officeChattanooga office(423) 344-3787Call now Chattanooga officeNationwide(615) 223-9600Call now Smyrna (Nashville & Middle TN) office
Talk to Turner Security

Ready to secure your business?

Send a quick message and the right Turner team will get back to you. Prefer to talk? Call the office closest to you.

Smyrna office(615) 223-9600Call now Smyrna (Nashville & Middle TN) officeChattanooga office(423) 344-3787Call now Chattanooga officeNationwide(615) 223-9600Call now Smyrna (Nashville & Middle TN) office

Fields marked with an asterisk are required.